- Home
- Catalogs
- 2021 - 2022 College Catalog
- Programs
- Industrial Instrumentation Technician Certificate
Industrial Instrumentation Technician Certificate (IIT1) Technical Certificate of Credit
(Stand Alone)
Program Description:
The IndustrialInstrumentation Technician certificate program provides knowledge and skills to install, configure, calibrate, repair, maintain, and troubleshoot electrical instruments and equipment. Emphasis is placed on principles and practices of instrumentation for industrial process control systems and for communications, networking, and signal transmission systems.
Entrance date: Each semester
Program admission requirements:
Minimum Test Scores
| ACCUPLACER NEXT GENERATION– | Reading | 224 | ACCUPLACER- | Sentence Skills | 60 |
| Writing | 236 | Reading Comprehension | 55 | ||
| Arithmetic | 229 | Arithmetic | 34 |
High School diploma or equivalent required for admission.
Credits required for graduation: 22
| Courses 22 credits | |
|---|---|
| IDSY 1101DC Circuit Analysis
This course introduces direct current (DC) concepts and applications. Topics include: electrical principles and laws; batteries; DC test equipment; series; parallel, and simple combination circuits; and laboratory procedures and safety practices. |
3 |
| IDSY 1105AC Circuit Analysis
This course introduces alternating current concepts, theory, and application of varying sine wave voltages and current, and the physical characteristics and applications of solid state devices. Topics include, but are not limited to, electrical laws and principles, magnetism, inductance and capacitance. |
3 |
| IDSY 1110Industrial Motor Controls I
This course introduces the fundamental concepts, principles, and devices involved in industrial motor controls, theories and applications of single and three-phase motors, wiring motor control circuits, and magnetic starters and braking. Topics include, but are not limited to, motor theory and operating principles, control devices, symbols and schematic diagrams, NEMA standards, Article 430 NEC and preventative maintenance and troubleshooting. |
4 |
| IDSY 1120Basic Industrial PLC's
Corequisite: IDSY 1110 This course introduces the operational theory, systems terminology, PLC installation, and programming procedures for Programmable Logic Controllers. Emphasis is placed on PLC programming, connections, installation, and start-up procedures. Other topics include timers and counters, relay logic instructions, and hardware and software applications. |
4 |
| IDSY 1230Industrial Instrumentation
Provides instruction in the principles and practices of instrumentation for industrial process control systems with an emphasis on industrial maintenance techniques for production equipment. Topics include: instrument tags; process documentation; basic control theory; sensing pressure, flow, level, and temperature; instrument calibration; and loop tuning. |
4 |
| IDSY 2830Networking Industrial Equipment
Provides communication and networking skills needed for cabling and connection to PLC/HMI Devices. |
4 |
Faculty
Chair/Instructor Mechatronics Technology
Manufacturing Technology Building, Room 115
-
Engineering & Electronics
-
Mechatronics
- Industrial Maintenance Electrical Assistant Certificate
- Mechatronics Technology Diploma
- Mechatronics Technology Degree
- Basic Mechatronics Specialist
- Fundamentals of Robotics
- Industrial Electrical Assistant
- Industrial Mechatronics Certificate
- Industrial Instrumentation Technician Certificate
- Industrial Systems Mechanic Certificate
- Mechatronics Technician Certificate
- Mechatronics Specialist Certificate
- Programmable Control Technician
- Robotics Technician
-
Mechatronics
Up one level
Programs of Study
Notice and Responsibilities Regarding this Catalog
The purpose of this catalog/handbook is to provide general information. It should not be construed as the basis of a contract between students and Albany Technical College (ATC). While the provisions of this catalog/handbook will ordinarily be applied as stated, ATC reserves the right to change any provisions listed without notice. Such changes may include entrance requirements and admissions procedures, courses, and programs of study, academic requirements for graduation, fees and charges, financial aid, rules and regulations and the College calendar. It is the student’s responsibility to keep informed of all changes including academic requirements for graduation.
- Table of Contents
- President's Message
- Accreditation And Affiliations
- Articulation Agreements
- Technical Education Guarantee
- Statement Of Equal Opportunity
- Equal Opportunity Employer
- Sexual Harassment And Misconduct
- Mission
- Adult Education Programs
- Information Directory
- Academic Calendar
- Admissions Policies and Procedures
- Admission Categories
- General Admission Requirements For The Associate Degree Programs
- General Admission Requirements For The Diploma Programs
- General Admission Requirements For The Certificate Programs
- Georgia Residency Requirements
- Registration
- Transfer Credit
- High School Programs
- Tuition And Fees
- Financial Obligations To ATC
- Financial Assistance
- Financial Aid Programs
- Financial Aid Fund Disbursements
- Satisfactory Academic Progress Policy And Procedures
- Grading System
- Grade Appeals
- Student Records
- Graduation Policy
- Student Services
- Student Life
- Student Disciplinary Procedure
- Student Complaints
- Student Rights And Responsibilities
- Albany Technical College Model Student Conduct Codes
- Procedure: Unlawful Harassment And Discrimination Of Students
- General Information
- Center for Business Solutions
- Program Advisors
- Faculty & Staff Directory
- Faculty
- Programs of Study
- Programs of Study
- Areas of Study
- Courses